Process & Material
C260 Brass Sinker EDM Thickness Review (100–200 Mm)
C260 Brass at 100–200 mm changes how Sinker EDM must be supported, flushed, finished, and inspected. The controlling dimension is cavity depth and width, rib thickness, electrode access, electrode wear, flushing and debris evacuation, not merely the outside stock size.
Quick Answer
For Sinker EDM on C260 Brass, treat 100–200 mm as a setup input rather than a guaranteed accuracy band. Confirm the real cavity depth and width, rib thickness, electrode access, electrode wear, flushing and debris evacuation, material condition, datum, functional faces, and inspection method before assigning tolerance or finish.
Key Thickness Decisions
What This Thickness Range Means
Large stock height affects reach and fixture design, not the cavity decision itself; use actual cavity geometry for planning. On C260 Brass, the supplied condition still changes support and surface response. This is the Sinker EDM thickness decision; it does not turn the range into a machine promise.
Choosing the Right Setup
For Sinker EDM on C260 Brass at 100–200 mm, plan electrode material, wear compensation, cavity depth, rib width, orbit strategy, and debris evacuation. Then state the supplied condition, support the functional features, and define surface and inspection requirements separately. Apply the tightest tolerance and finest finish only to the dimensions and faces that control function.
What to Watch For
At 100–200 mm, the failure is not simply “too thick” or “too deep.” This is specialized deep Sinker EDM. Electrode stiffness, ram travel, oil circulation, debris evacuation, and wear compensation dominate cycle time. Segment the electrode or cavity where possible and use intermediate depth and form inspection rather than one final check. If the setup ignores that physical progression, the named feature can pass at the accessible face while failing at depth, at the exit, or after unclamping. The C260 Brass condition must be included in the same inspection decision.
Technical Context
A shaped graphite or copper electrode approaches the conductive workpiece in dielectric fluid without touching it. At 100–200 mm, This is specialized deep Sinker EDM. Electrode stiffness, ram travel, oil circulation, debris evacuation, and wear compensation dominate cycle time. Segment the electrode or cavity where possible and use intermediate depth and form inspection rather than one final check. Control electrode stiffness, wear, orbit, debris exit, cavity access, and bottom inspection. For C260 Brass, the supplied condition still determines support and surface acceptance.
Sinker EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | blind cavities, ribs, shaped pockets, mold details, deep forms, and internal geometry that a traveling wire cannot reach |
| Tolerance | ±0.008–0.030 mm |
| Surface finish | Ra 0.2–6.3 μm |
| Electrode choice | Graphite or copper selected from cavity, finish, and wear needs |
| Primary cavity limit | Depth, rib width, access, and debris evacuation |
| Main limitation | Electrode access and debris evacuation limit deep, narrow blind geometry. |
Thickness Range Reference
| Thickness or depth input | What it means for this process |
|---|---|
| 100–200 mm | Large stock height affects reach and fixture design, not the cavity decision itself; use actual cavity geometry for planning. |
| Primary controls | Plan from cavity geometry, electrode access, orbit strategy, rough and finish electrodes, and the strength of the remaining walls. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use gentle fixturing and adjust energy for high conductivity. | Soft edges can mark or roll under poor support. | Keep contact, bearing, and cosmetic faces as separate finish requirements. |
| half-hard or work-hardened | Balance work-hardening stress with wear compensation. | Thin sections can move and micro features can round as electrodes wear. | Inspect edge radius and functional texture. |
| hard-drawn | Use conservative finishing on hard-drawn or aged stock. | Over-finishing can remove useful texture or shift contact dimensions. | Apply finishing only to functional faces. |
Thickness Impact
C260 Brass is cartridge brass with good conductivity and strong cold-forming response. In the 100–200 mm setup, state the supplied condition, support the functional features, and define surface and inspection requirements separately. The material condition changes support and surface response, while Sinker EDM determines how the feature is accessed and controlled.
Surface and Edge Control
For Sinker EDM on C260 Brass at 100–200 mm, inspect the functional face or edge from its own datum. Use gentle fixturing and a finish strategy that protects contact, sealing or heat-transfer surfaces. Keep texture, edge condition, recast, corrosion protection, and post-processing as separate acceptance items when service requires them.
C260 Brass Sinker EDM Thickness Checkpoints
- Show the actual cavity depth and local wall thickness represented by 100–200 mm, not only the outside part size.
- Plan from cavity geometry, electrode access, orbit strategy, rough and finish electrodes, and the strength of the remaining walls.
- Mark the functional tolerance, finish, datum, and inspection method on the drawing.
Limits and Better Alternatives
Main Limit
The 100–200 mm label cannot replace the real cavity depth and width, rib thickness, electrode access, electrode wear, flushing and debris evacuation or the supplied C260 Brass condition. Rolled temper and grain direction can affect thin sections, springback and edge stability.
Consider Another Route When
Use Wire EDM for through profiles, CNC for open cavities with tool access, or grinding for simple flat precision surfaces.
Practical Next Step
Send the C260 Brass drawing with its condition, the actual cavity depth and local wall thickness in the 100–200 mm range, feature geometry, controlled tolerance, surface requirement, quantity, and inspection method.
Practical Takeaway
For C260 Brass at 100–200 mm, plan Sinker EDM from the real feature axis, support, debris control, and inspection method instead of treating the range as a blanket capability statement.
Request a Machining Feasibility Review
Send material grade, drawing files, tolerance and quantity. We confirm process fit before quoting.
- Process: Sinker EDM
- Material: C260 Brass
- Thickness: 100–200 mm
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
- Tolerance and critical dimensions
- Surface finish or inspection requirement
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.