Process & Material
C360 Brass Micro EDM Feasibility Review
C360 Brass can be machined with Micro EDM when the geometry matches micro holes, micro slots, miniature cavities, fine pins, and sub-millimeter precision details. C360 Brass is free-machining brass with good conductivity and comparatively easy conventional machinability; the supplied condition affects support, discharge energy, finishing, and inspection.
Quick Answer
Micro EDM is suitable for C360 Brass when the feature is a micro hole, micro slot, miniature cavity, fine pin, or other sub-millimeter detail. The supplied condition must be stated before tolerance and surface requirements are confirmed.
Key Material Decisions
How This Material Behaves
Free-machining brass with good conductivity and comparatively easy conventional machinability. In Micro EDM, the supplied condition directly changes discharge stability, electrode wear, edge quality, and the finishing plan—especially at micro scale.
Choosing the Right Condition
Choose Micro EDM for micro holes, micro slots, miniature cavities, fine pins, and sub-millimeter precision details. State the exact C360 Brass condition, then set tolerance, finish, support, and inspection from the controlled feature rather than the whole part.
Risks to Manage
When Micro EDM is used on a sub-millimeter slot, hole, or datum feature in C360 Brass, two effects occur together: EDM is best reserved for geometry that justifies it rather than simple open features, while micron-level electrode wear and debris change the gap while the small section relaxes or rounds at the edge. The combined result is that the feature can drift in size and pitch while also losing the edge geometry that makes it functional. Control it by stage or replace the electrode, use low-energy finishing, control micro-flushing and temperature, and verify the feature with metrology that resolves the remaining tolerance.
How Micro EDM Works on C360 Brass
Micro EDM uses very small electrodes and low-energy discharges to create miniature conductive features without cutting force. On C360 Brass, the supplied condition changes dimensional stability, discharge response, and surface behavior.
Micro EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | micro holes, micro slots, miniature cavities, fine pins, and sub-millimeter precision details |
| Tolerance | ±0.002–0.010 mm |
| Surface finish | Ra 0.1–1.6 μm |
| Feature scale | Sub-millimeter holes, slots, and cavities |
| Primary micro limit | Electrode wear and measurement resolution |
| Main limitation | Loose-tolerance or easily accessible features are rarely economical with Micro EDM. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use gentle fixturing and adjust energy for high conductivity. | Soft edges can mark or roll under poor support. | Keep contact, bearing, and cosmetic faces as separate finish requirements. |
| half-hard | Balance work-hardening stress with wear compensation. | Thin sections can move and micro features can round as electrodes wear. | Inspect edge radius and functional texture. |
| finished bar condition | Use conservative finishing on hard-drawn or aged stock. | Over-finishing can remove useful texture or shift contact dimensions. | Apply finishing only to functional faces. |
How This Material Behaves
C360 Brass does not behave the same in Micro EDM across every supplied condition. In EDM, this means the process adds value mainly on inaccessible slots, sharp internal details, or hardened assemblies rather than open geometry. Keep spark energy conservative on fine edges, clean the cut before plating or contact service, and use EDM only where tool access or burr control justifies the slower route. At micro scale, material edge behavior and residual stress are the same order as electrode wear, spark gap, flushing, and measurement uncertainty. The process plan must reserve tolerance for all of them.
Surface Integrity and Post-Process
For C360 Brass in Micro EDM, use gentle fixturing and a finish strategy that protects contact, sealing or heat-transfer surfaces. Assign fine finish, recast, edge, and post-process requirements only to the functional Micro EDM faces that need them.
C360 Brass Micro EDM Checkpoints
- Confirm that the feature matches micro holes, micro slots, miniature cavities, fine pins, and sub-millimeter precision details.
- State the supplied condition: annealed, half-hard, and finished bar condition.
- Mark the controlled dimensions, functional surfaces, datum scheme, and inspection method.
Typical Parts and Features
- electrical contacts
- electrodes
- busbar details
- micro holes
- micro slots
- miniature cavities
Limits and Better Alternatives
Main Limit
Loose-tolerance or easily accessible features are rarely economical with Micro EDM. On C360 Brass, EDM is best reserved for geometry that justifies it rather than simple open features; the supplied condition still controls support, finishing, and surface-integrity review.
Consider Another Route When
Use conventional EDM for larger features, precision laser processing for suitable thin geometry, or mechanical micro-drilling where a tool can reach.
Practical Next Step
Send the C360 Brass drawing with condition, controlled geometry, tolerance, functional surface callouts, quantity, and inspection requirements. If the route is unclear, we will compare Micro EDM with the adjacent EDM or conventional process.
Practical Takeaway
C360 Brass is compatible with Micro EDM when the feature matches the process access. The supplied condition determines support, finishing, surface control, and inspection.
Request a Machining Feasibility Review
Send material grade, drawing files, tolerance and quantity. We confirm process fit before quoting.
- Process: Micro EDM
- Material: C360 Brass
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
- Tolerance and critical dimensions
- Surface finish or inspection requirement
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.
Frequently Asked Questions
Can C360 Brass be machined with Micro EDM?
Yes, when the feature is a micro hole, micro slot, miniature cavity, fine pin, or other sub-millimeter detail. C360 Brass is electrically conductive and the final route follows the feature geometry and supplied condition.
What controls Micro EDM on C360 Brass?
The main process controls are electrode wear, feature-to-electrode ratio, micro-flushing, aspect ratio, edge radius, thermal stability, and measurement resolution. The C360 Brass condition adds dimensional-stability and surface-integrity requirements.
What is the main risk?
When Micro EDM is used on a sub-millimeter slot, hole, or datum feature in C360 Brass, two effects occur together: EDM is best reserved for geometry that justifies it rather than simple open features, while micron-level electrode wear and debris change the gap while the small section relaxes or rounds at the edge. The combined result is that the feature can drift in size and pitch while also losing the edge geometry that makes it functional. Control it by stage or replace the electrode, use low-energy finishing, control micro-flushing and temperature, and verify the feature with metrology that resolves the remaining tolerance.
What should I send for review?
Send the drawing, exact C360 Brass condition, controlled geometry, tolerance, functional surface requirements, quantity, and inspection expectations. If any item is undecided, send what you have and we will help complete the review.