Process & Material
Invar 36 Micro EDM High Precision Tolerance + Fine Finish Review
This Invar 36 Micro EDM page combines a High-precision tolerance target with a Fine surface target. These requirements must be planned together because finishing passes improve texture while also changing profile offset, cavity size, hole size, or edge geometry.
Quick Answer
For Invar 36, ±0.005–0.010 mm and Ra 0.8–1.6 μm are achievable on selected Micro EDM features when electrode wear, gap stability, micro-flushing, thermal control, and measurement resolution are planned together. Apply both targets from the same datum, and reserve the tightest values for the dimensions and faces that control function.
Key Quality Decisions
What These Targets Mean
On Invar 36, ±0.005–0.010 mm controls the named dimensions and Ra 0.8–1.6 μm controls the named functional faces. In Micro EDM, electrode wear and measurement resolution can consume the tolerance while low-energy finishing changes edge radius and texture. The supplied condition adds a separate risk: residual stress and asymmetric stock removal can undermine the low-expansion design intent.
Getting Both Targets Right
Use one machining and inspection datum. Apply ±0.005–0.010 mm only to dimensions that control fit, and Ra 0.8–1.6 μm only to functional faces. Plan electrode wear, feature-to-electrode ratio, micro-flushing, aspect ratio, edge radius, thermal stability, and measurement resolution. State the exact Invar 36 condition and the inspection method before releasing the result.
What Gets Missed
On a sub-millimeter hole, slot, or pitch feature specified at ±0.005–0.010 mm and Ra 0.8–1.6 μm, electrode wear and measurement uncertainty can consume the remaining tolerance while the edge rounds during finishing. The tolerance represents a small remaining offset allowance, while the finishing pass removes enough stock to change edge radius and local size; treating them as independent callouts can make the last finishing step destroy the dimension it is meant to improve. Inspect size, pitch, depth, edge radius, electrode wear, and measurement uncertainty after the final surface step. For Invar 36, also account for this material-specific risk: residual stress and asymmetric stock removal can undermine the low-expansion design intent.
How the Targets Interact
For Invar 36, ±0.005–0.010 mm and Ra 0.8–1.6 μm are linked through the Micro EDM finishing route. Electrode wear and measurement resolution can consume the tolerance while low-energy finishing changes edge radius and texture. The release plan must bind material condition, geometry, datum, finishing stage, and measurement to the same named features.
Micro EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | micro holes, micro slots, miniature cavities, fine pins, and sub-millimeter precision details |
| Tolerance | ±0.002–0.010 mm |
| Surface finish | Ra 0.1–1.6 μm |
| Feature scale | Sub-millimeter holes, slots, and cavities |
| Primary micro limit | Electrode wear and measurement resolution |
| Main limitation | Loose-tolerance or easily accessible features are rarely economical with Micro EDM. |
Quality Target Reference
| Requirement | Planning range | What it means in practice |
|---|---|---|
| High-precision tolerance | ±0.005–0.010 mm | Plan finishing passes, thermal stability and inspection from the same datum scheme. |
| Fine finish | Ra 0.8–1.6 μm | Usually needs a finishing pass or lower-energy discharge on the specified surface. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| solution annealed | Use stable support and conservative energy. | High-temperature alloys can retain a hard recast layer. | Identify fatigue and hot-section faces before finishing. |
| cold-worked or stabilized | Account for cold-work and service stress. | Thin features can move and electrode wear can grow corners. | Use low-energy finishing and selective metallurgical inspection. |
Tolerance & Surface Requirements
For Micro EDM at ±0.005–0.010 mm and Ra 0.8–1.6 μm, apply the finish only to the faces named on the drawing. On Invar 36, use lower-energy finishing and inspect critical surfaces when fatigue, sealing or corrosion performance is specified. Roughness does not replace recast, edge, corrosion, crack, or post-process acceptance where those items affect function.
Invar 36 Micro EDM Quality Checkpoints
- Mark the dimensions that actually need ±0.005–0.010 mm and use the same datum for machining and inspection.
- Circle the faces that need Ra 0.8–1.6 μm; leave nonfunctional surfaces at a practical production finish.
- State the Invar 36 condition, Micro EDM finishing strategy, measurement method, and any recast or edge requirement.
Limits and Better Alternatives
Main Limit
±0.005–0.010 mm and Ra 0.8–1.6 μm are selected-feature planning references for Invar 36 in Micro EDM, not unconditional whole-part guarantees.
Consider Another Route When
Use conventional EDM for larger features, precision laser processing for suitable thin geometry, or mechanical micro-drilling where a tool can reach.
Practical Next Step
Send the Invar 36 drawing with the Micro EDM features that need ±0.005–0.010 mm, the faces that need Ra 0.8–1.6 μm, the supplied condition, quantity, datums, and inspection method.
Practical Takeaway
On Invar 36, plan ±0.005–0.010 mm and Ra 0.8–1.6 μm together for the selected Micro EDM features. Use one datum and one inspection plan, and apply the tightest values only where they control function.
Additional Project Information
Include application, destination and end-use notes together with the material, quantity and drawing requirements.
Project Details for Technical Review
Include application and end-use notes when they affect material, inspection, documentation, or export review.
- Process: Micro EDM
- Material: Invar 36
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
- Tolerance and critical dimensions
- Surface finish or inspection requirement
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.
Frequently Asked Questions
Can Micro EDM hold the selected tolerance on Invar 36?
Use ±0.005–0.010 mm as a selected-feature planning reference. The confirmed result depends on material condition and geometry. Process control covers electrode wear, feature-to-electrode ratio, micro-flushing, aspect ratio, edge radius, thermal stability, and measurement resolution. Machining and inspection should use one consistent datum.
Should Ra 0.8–1.6 μm apply to every surface?
No. Apply the fine finish only to functional faces. Other areas can remain at a practical production finish, which reduces cycle time and avoids unnecessary processing.
How does the condition of Invar 36 affect both targets?
Invar 36 is a low-expansion iron-nickel alloy selected for dimensional stability across temperature changes. The condition changes support, stress response, finishing energy, dimensional stability, and surface-integrity planning.
What should the drawing identify?
Identify the dimensions that need ±0.005–0.010 mm, the faces that need Ra 0.8–1.6 μm, the datums, the exact Invar 36 condition, the Micro EDM feature, and the inspection method. Machining and inspection should use the same datum scheme.