Process & Material
Titanium Grade 2 Wire EDM Feasibility Review
Titanium Grade 2 can be machined with Wire EDM when the geometry matches through profiles, precision slots, punches, inserts, cutouts, narrow webs, and tapered walls. Titanium Grade 2 is a commercially pure titanium grade with lower strength and higher ductility than alpha-beta Grade 5; the supplied condition affects support, discharge energy, finishing, and inspection.
Quick Answer
Wire EDM is suitable for Titanium Grade 2 when the wire can pass completely through the workpiece from an edge or a start hole. The supplied condition must be stated before tolerance and surface requirements are confirmed.
Key Material Decisions
How This Material Behaves
A commercially pure titanium grade with lower strength and higher ductility than alpha-beta Grade 5. In Wire EDM, the supplied condition changes stress release during the through cut, edge response to trim passes, and the final corrosion or surface-protection route.
Choosing the Right Condition
Choose Wire EDM for through profiles, precision slots, punches, inserts, cutouts, narrow webs, and tapered walls. State the exact Titanium Grade 2 condition, then set tolerance, finish, support, and inspection from the controlled feature rather than the whole part.
Risks to Manage
When Wire EDM is used on a thin through profile or narrow web in Titanium Grade 2, two effects occur together: thin sections can move and corrosion or medical surfaces need selective recast removal and cleanliness, while wire lag and flushing change the top-to-bottom kerf while the profile loses restraint. The combined result is that the feature can bow and finish with taper or an offset edge even though the top contour measures correctly. Control it by rough symmetrically, leave a controlled finish allowance, support near the cut, and inspect both top and bottom profiles from the released datum.
How Wire EDM Works on Titanium Grade 2
Wire EDM uses a continuously moving wire electrode and controlled discharges to cut a through profile without mechanical cutting force. On Titanium Grade 2, the supplied condition changes dimensional stability, discharge response, and surface behavior.
Wire EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | through profiles, precision slots, punches, inserts, cutouts, narrow webs, and tapered walls |
| Tolerance | ±0.005–0.025 mm |
| Surface finish | Ra 0.2–3.2 μm |
| Wire diameter | 0.10–0.30 mm planning range |
| Minimum internal corner | Approximately wire radius plus spark gap |
| Main limitation | Blind cavities and closed pockets are not wire-cut features. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use stable support and low-energy finishing. | Thermal surface effects can reduce fatigue resistance. | Specify recast and edge condition on fatigue and medical faces. |
| stress-relieved | Plan around stress relief and thin-wall movement. | Residual stress can distort delicate profiles. | Use trim passes and controlled post-processing on critical faces. |
How This Material Behaves
Titanium Grade 2 does not behave the same in Wire EDM across every supplied condition. In EDM, this means thin parts can move easily and fatigue or corrosion faces are sensitive to recast and contamination despite the material's machinability by spark erosion. Use stable support, clean dielectric, low-energy finishing, and remove or limit recast on service-critical surfaces. Because the profile opens continuously, material stress release and support act at the same time as wire tension, flushing, and trim-pass offset. State the heat-treatment condition before choosing supports and final offsets.
Surface Integrity and Post-Process
For Titanium Grade 2 in Wire EDM, use low-energy finishing and define whether recast removal, polishing or passivation is required. Assign fine finish, recast, edge, and post-process requirements only to the functional Wire EDM faces that need them.
Titanium Grade 2 Wire EDM Checkpoints
- Confirm that the feature matches through profiles, precision slots, punches, inserts, cutouts, narrow webs, and tapered walls.
- State the supplied condition: annealed and stress-relieved.
- Mark the controlled dimensions, functional surfaces, datum scheme, and inspection method.
Typical Parts and Features
- medical components
- aerospace profiles
- lightweight fixtures
- punches and die inserts
- precision profile gauges
- gear and spline outlines
Limits and Better Alternatives
Main Limit
Blind cavities and closed pockets are not wire-cut features because the wire needs a continuous through path. On Titanium Grade 2, thin sections can move and corrosion or medical surfaces need selective recast removal and cleanliness; the supplied condition still controls support, finishing, and surface-integrity review.
Consider Another Route When
Use Sinker EDM for blind cavities, CNC machining for accessible open geometry, or laser cutting when thin-sheet speed matters more than EDM edge quality.
Practical Next Step
Send the Titanium Grade 2 drawing with condition, controlled geometry, tolerance, functional surface callouts, quantity, and inspection requirements. If the route is unclear, we will compare Wire EDM with the adjacent EDM or conventional process.
Practical Takeaway
Titanium Grade 2 is compatible with Wire EDM when the feature matches the process access. The supplied condition determines support, finishing, surface control, and inspection.
Additional Project Information
Include application, destination and end-use notes together with the material, quantity and drawing requirements.
Project Details for Technical Review
Include application and end-use notes when they affect material, inspection, documentation, or export review.
- Process: Wire EDM
- Material: Titanium Grade 2
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
- Tolerance and critical dimensions
- Surface finish or inspection requirement
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.
Frequently Asked Questions
Can Titanium Grade 2 be machined with Wire EDM?
Yes, when the wire can pass completely through the workpiece from an edge or a start hole. Titanium Grade 2 is electrically conductive and the final route follows the feature geometry and supplied condition.
What controls Wire EDM on Titanium Grade 2?
The main process controls are wire diameter, kerf compensation, flushing, wire tension, guide alignment, taper control, and trim-pass stability. The Titanium Grade 2 condition adds dimensional-stability and surface-integrity requirements.
What is the main risk?
When Wire EDM is used on a thin through profile or narrow web in Titanium Grade 2, two effects occur together: thin sections can move and corrosion or medical surfaces need selective recast removal and cleanliness, while wire lag and flushing change the top-to-bottom kerf while the profile loses restraint. The combined result is that the feature can bow and finish with taper or an offset edge even though the top contour measures correctly. Control it by rough symmetrically, leave a controlled finish allowance, support near the cut, and inspect both top and bottom profiles from the released datum.
What should I send for review?
Send the drawing, exact Titanium Grade 2 condition, controlled geometry, tolerance, functional surface requirements, quantity, and inspection expectations. If any item is undecided, send what you have and we will help complete the review.