Process & Material
Titanium Grade 5 Sinker EDM High Precision Tolerance + Skim Cut / Fine Pass Finish Review
This Titanium Grade 5 Sinker EDM page combines a High-precision tolerance target with a Skim-cut / fine pass finish surface target. These requirements must be planned together because finishing passes improve texture while also changing profile offset, cavity size, hole size, or edge geometry.
Quick Answer
For Titanium Grade 5, ±0.005–0.010 mm and Ra 0.4–0.8 μm are achievable on selected Sinker EDM features when electrode wear, orbit strategy, cavity flushing, and finishing energy are planned together. Apply both targets from the same datum, and reserve the tightest values for the dimensions and faces that control function.
Key Quality Decisions
What These Targets Mean
On Titanium Grade 5, ±0.005–0.010 mm controls the named dimensions and Ra 0.4–0.8 μm controls the named functional faces. In Sinker EDM, electrode wear, orbit, and finishing energy change cavity size, corner condition, and texture together. The supplied condition adds a separate risk: fatigue-critical edges and low thermal conductivity require low-energy finish planning.
Getting Both Targets Right
Use one machining and inspection datum. Apply ±0.005–0.010 mm only to dimensions that control fit, and Ra 0.4–0.8 μm only to functional faces. Plan electrode material, wear compensation, cavity depth, rib width, orbit strategy, and debris evacuation. State the exact Titanium Grade 5 condition and the inspection method before releasing the result.
What Gets Missed
On a blind cavity, floor, or deep rib specified at ±0.005–0.010 mm and Ra 0.4–0.8 μm, electrode wear can leave the floor shallow, the wall oversized, or the rib tip thinner after finishing. The tolerance represents a small remaining offset allowance, while successive low-energy passes change kerf, taper, and corner geometry while improving texture; treating them as independent callouts can make the last finishing step destroy the dimension it is meant to improve. Inspect floor depth, wall size, corner, rib thickness, and electrode-wear compensation after the final surface step. For Titanium Grade 5, also account for this material-specific risk: fatigue-critical edges and low thermal conductivity require low-energy finish planning.
How the Targets Interact
For Titanium Grade 5, ±0.005–0.010 mm and Ra 0.4–0.8 μm are linked through the Sinker EDM finishing route. Electrode wear, orbit, and finishing energy change cavity size, corner condition, and texture together. The release plan must bind material condition, geometry, datum, finishing stage, and measurement to the same named features.
Sinker EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | blind cavities, ribs, shaped pockets, mold details, deep forms, and internal geometry that a traveling wire cannot reach |
| Tolerance | ±0.008–0.030 mm |
| Surface finish | Ra 0.2–6.3 μm |
| Electrode choice | Graphite or copper selected from cavity, finish, and wear needs |
| Primary cavity limit | Depth, rib width, access, and debris evacuation |
| Main limitation | Electrode access and debris evacuation limit deep, narrow blind geometry. |
Quality Target Reference
| Requirement | Planning range | What it means in practice |
|---|---|---|
| High-precision tolerance | ±0.005–0.010 mm | Plan finishing passes, thermal stability and inspection from the same datum scheme. |
| Skim-cut / fine pass finish finish | Ra 0.4–0.8 μm | Use dedicated trim or finishing passes and inspect only the surfaces carrying this callout. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use stable support and low-energy finishing. | Thermal surface effects can reduce fatigue resistance. | Specify recast and edge condition on fatigue and medical faces. |
| stress-relieved | Plan around stress relief and thin-wall movement. | Residual stress can distort delicate profiles. | Use trim passes and controlled post-processing on critical faces. |
Tolerance & Surface Requirements
For Sinker EDM at ±0.005–0.010 mm and Ra 0.4–0.8 μm, apply the finish only to the faces named on the drawing. On Titanium Grade 5, use low-energy finishing and define whether recast removal, polishing or passivation is required. Roughness does not replace recast, edge, corrosion, crack, or post-process acceptance where those items affect function.
Titanium Grade 5 Sinker EDM Quality Checkpoints
- Mark the dimensions that actually need ±0.005–0.010 mm and use the same datum for machining and inspection.
- Circle the faces that need Ra 0.4–0.8 μm; leave nonfunctional surfaces at a practical production finish.
- State the Titanium Grade 5 condition, Sinker EDM finishing strategy, measurement method, and any recast or edge requirement.
Limits and Better Alternatives
Main Limit
±0.005–0.010 mm and Ra 0.4–0.8 μm are selected-feature planning references for Titanium Grade 5 in Sinker EDM, not unconditional whole-part guarantees.
Consider Another Route When
Use Wire EDM for through profiles, CNC for open cavities with tool access, or grinding for simple flat precision surfaces.
Practical Next Step
Send the Titanium Grade 5 drawing with the Sinker EDM features that need ±0.005–0.010 mm, the faces that need Ra 0.4–0.8 μm, the supplied condition, quantity, datums, and inspection method.
Practical Takeaway
On Titanium Grade 5, plan ±0.005–0.010 mm and Ra 0.4–0.8 μm together for the selected Sinker EDM features. Use one datum and one inspection plan, and apply the tightest values only where they control function.
Additional Project Information
Include application, destination and end-use notes together with the material, quantity and drawing requirements.
Project Details for Technical Review
Include application and end-use notes when they affect material, inspection, documentation, or export review.
- Process: Sinker EDM
- Material: Titanium Grade 5
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
- Tolerance and critical dimensions
- Surface finish or inspection requirement
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.
Frequently Asked Questions
Can Sinker EDM hold the selected tolerance on Titanium Grade 5?
Use ±0.005–0.010 mm as a selected-feature planning reference. The confirmed result depends on material condition and geometry. Process control covers electrode material, wear compensation, cavity depth, rib width, orbit strategy, debris evacuation, and rough-versus-finish electrodes. Machining and inspection should use one consistent datum.
Should Ra 0.4–0.8 μm apply to every surface?
No. Apply the fine finish only to functional faces. Other areas can remain at a practical production finish, which reduces cycle time and avoids unnecessary processing.
How does the condition of Titanium Grade 5 affect both targets?
Titanium Grade 5 is the common Ti-6Al-4V alpha-beta alloy whose annealed or heat-treated state changes strength and residual stress. The condition changes support, stress response, finishing energy, dimensional stability, and surface-integrity planning.
What should the drawing identify?
Identify the dimensions that need ±0.005–0.010 mm, the faces that need Ra 0.4–0.8 μm, the datums, the exact Titanium Grade 5 condition, the Sinker EDM feature, and the inspection method. Machining and inspection should use the same datum scheme.