Process & Material
Titanium Grade 2 Wire EDM Thickness Review (1–5 Mm)
Titanium Grade 2 at 1–5 mm changes how Wire EDM must be supported, flushed, finished, and inspected. The controlling dimension is section thickness, wire path, kerf, flushing, taper and verticality, not merely the outside stock size.
Quick Answer
For Wire EDM on Titanium Grade 2, treat 1–5 mm as a setup input rather than a guaranteed accuracy band. Confirm the real section thickness, wire path, kerf, flushing, taper and verticality, material condition, datum, functional faces, and inspection method before assigning tolerance or finish.
Key Thickness Decisions
What This Thickness Range Means
This section is usually straightforward; corner radius, part support and finish-pass strategy have more influence than cutting height. On Titanium Grade 2, the supplied condition still changes support and surface response. This is the Wire EDM thickness decision; it does not turn the range into a machine promise.
Choosing the Right Setup
For Wire EDM on Titanium Grade 2 at 1–5 mm, plan wire diameter, kerf compensation, flushing, wire tension, guide alignment, taper, and trim-pass stability. Then limit aggressive energy on fatigue faces, control recast or contamination, and keep post-process cleanliness explicit. Apply the tightest tolerance and finest finish only to the dimensions and faces that control function.
What to Watch For
At 1–5 mm, the failure is not simply “too thick” or “too deep.” This is a short section, so wire lag is small and one rough cut plus planned trim passes can usually control the profile. Entry and exit edges are still close enough that a burr-free appearance can hide edge rounding or clamp distortion; inspect the full face and datum after release. If the setup ignores that physical progression, the named feature can pass at the accessible face while failing at depth, at the exit, or after unclamping. The Titanium Grade 2 condition must be included in the same inspection decision.
Technical Context
A continuously moving wire is held in a controlled spark gap while pulsed discharges remove a through profile. At 1–5 mm, This is a short section, so wire lag is small and one rough cut plus planned trim passes can usually control the profile. Entry and exit edges are still close enough that a burr-free appearance can hide edge rounding or clamp distortion; inspect the full face and datum after release. Control support, wire tension, guide alignment, flushing, trim-pass offset, and top-to-bottom inspection. For Titanium Grade 2, the supplied condition still determines support and surface acceptance.
Wire EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | through profiles, precision slots, punches, inserts, cutouts, narrow webs, and tapered walls |
| Tolerance | ±0.005–0.025 mm |
| Surface finish | Ra 0.2–3.2 μm |
| Wire diameter | 0.10–0.30 mm planning range |
| Minimum internal corner | Approximately wire radius plus spark gap |
| Main limitation | Blind cavities and closed pockets are not wire-cut features. |
Thickness Range Reference
| Thickness or depth input | What it means for this process |
|---|---|
| 1–5 mm | This section is usually straightforward; corner radius, part support and finish-pass strategy have more influence than cutting height. |
| Primary controls | Match wire diameter, support, flushing, guide alignment, and trim passes to the section height and detail requirement. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use stable support and low-energy finishing. | Thermal surface effects can reduce fatigue resistance. | Specify recast and edge condition on fatigue and medical faces. |
| stress-relieved | Plan around stress relief and thin-wall movement. | Residual stress can distort delicate profiles. | Use trim passes and controlled post-processing on critical faces. |
Thickness Impact
Titanium Grade 2 is a commercially pure titanium grade with lower strength and higher ductility than alpha-beta Grade 5. In the 1–5 mm setup, limit aggressive energy on fatigue faces, control recast or contamination, and keep post-process cleanliness explicit. The material condition changes support and surface response, while Wire EDM determines how the feature is accessed and controlled.
Surface and Edge Control
For Wire EDM on Titanium Grade 2 at 1–5 mm, inspect the functional face or edge from its own datum. Use low-energy finishing and define whether recast removal, polishing or passivation is required. Keep texture, edge condition, recast, corrosion protection, and post-processing as separate acceptance items when service requires them.
Titanium Grade 2 Wire EDM Thickness Checkpoints
- Show the actual section height represented by 1–5 mm, not only the outside part size.
- Match wire diameter, support, flushing, guide alignment, and trim passes to the section height and detail requirement.
- Mark the functional tolerance, finish, datum, and inspection method on the drawing.
Limits and Better Alternatives
Main Limit
The 1–5 mm label cannot replace the real section thickness, wire path, kerf, flushing, taper and verticality or the supplied Titanium Grade 2 condition. Thin sections can move and corrosion or medical surfaces need selective recast removal and cleanliness.
Consider Another Route When
Use Sinker EDM for blind forms, CNC for accessible open geometry, or laser/waterjet when sheet-cutting speed matters more than EDM edge quality.
Practical Next Step
Send the Titanium Grade 2 drawing with its condition, the actual section height in the 1–5 mm range, feature geometry, controlled tolerance, surface requirement, quantity, and inspection method.
Practical Takeaway
For Titanium Grade 2 at 1–5 mm, plan Wire EDM from the real feature axis, support, debris control, and inspection method instead of treating the range as a blanket capability statement.
Additional Project Information
Include application, destination and end-use notes together with the material, quantity and drawing requirements.
Project Details for Technical Review
Include application and end-use notes when they affect material, inspection, documentation, or export review.
- Process: Wire EDM
- Material: Titanium Grade 2
- Thickness: 1–5 mm
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
- Tolerance and critical dimensions
- Surface finish or inspection requirement
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.
Frequently Asked Questions
Does 1–5 mm alone define Wire EDM capability?
No. It only describes one setup dimension. Final capability follows the actual section thickness, wire path, kerf, flushing, taper and verticality, material condition, access, datum, and inspection method.
What controls the setup in this range?
The main controls are wire diameter, kerf compensation, flushing, wire tension, guide alignment, taper, and trim-pass stability. Their importance changes with the real feature geometry rather than the nominal range label.
What should be watched on Titanium Grade 2?
A dimensionally correct feature can still be rejected for recast, contamination, or fatigue-sensitive edge damage Use limit aggressive energy on fatigue faces, control recast or contamination, and keep post-process cleanliness explicit and release only the functional dimensions and faces that have a defined acceptance method.
What should the drawing identify?
Show the true feature path or section represented by 1–5 mm, the Titanium Grade 2 condition, controlled datum, tolerance, finish, quantity, and inspection route.